S/V High Life

1966 Bristol 27

From Practical Sailor:

The Bristol 27 is a product of its era and of the traditional bent of designer Carl Alberg’s thinking–that is, a combination cruiser and club racer. At 6,600 pounds displacement with 2,575 pounds of internal lead ballast in its full keel, the boat is fairly heavy by contemporary standards. Fast enough on its own merits, it has an average PHRF rating of 234. By comparison, the lighter Catalina 27 with fin keel and spade rudder has a PHRF rating of about 210, and the Cal 27, also with a divided underbody, a rating of 192 to 200. Clearly, the Bristol was designed to be seaworthy rather than swift.

This slideshow requires JavaScript.

From Bluewaterboats.org:

Now forty five years on from its first introduction, the Bristol 27 can certainly be considered well proven. Though the boat was introduced more for coastal sailing, it was built strong, the design inherently seaworthy and well prepped boats have been offshore.

Brothers Clint and Everett Pearson made their mark founding Pearson Yachts, when they sold up in the mid-1960s they formed Bristol Yachts. The first boat out of the gates was the Bristol 27, some say it’s very much a copy of their earlier successful Pearson Triton 28. The Bristol 27 launched in 1966 and sold in large numbers, particularly in the first two years (more than 170), and it’s been estimated 337 have been built before production ceased in 1978.

The design was from Carl Alberg and reflects the Scandinavian Folkboat influence of the day. These boats were narrow with long overhangs, graceful low-slung sheerlines, and sweeping full keels that are cutaway in the forefoot. The narrow beam adds to seaworthiness but doesn’t do much for form stability, so they are quite tender initially. That’s not all bad as they were designed to lengthen their waterline when heeled.

The boats carried a masthead sloop rig, originally with roller-reefing in the mainsail boom. These days most have reverted back to simple slab reefed mainsails which hold a better shape and do not suffer from jamming.

Bristol 27 Interior LayoutBristol 27s came in three flavors, a day sailing model with a large cockpit and small interior, a standard model which had a larger cabin and twin settees, and a dinette model which substituted a settee for a table. Power options included an outboard engine mounted inside a cockpit well or an inboard engine in either petrol or diesel. The inboard engines are preferred for any offshore work, especially the diesel.

All Bristol boats were strong, the Bristol 27, being one of the first generation of fiberglass boats, was no exception. They had solid GRP hulls and the deck, cabin, and cockpit was an integral molding and connected to the hull via deck clamp and through bolting. The mast was deck stepped, but in this case supported by a substantial bulkhead that’s well tabbed into the hull. Lead was used as ballast and encapsulated in fiberglass.

Boats of this era were not designed for interior space and the Bristol 27′s interior is cramped by modern standards. Even in the cruising model with the larger cabin there’s a relatively large cockpit which takes space from the cabin. One of the practical decisions made in the design was for a raised portion of in the cabin house to allow 5′ 10″ of standing room in the main cabin or more if below the companionway with the hatch slid open! The V-berths accommodate 6′ 6″ while the settees 6′ 4″.

Underway the Bristol is nimble and easy to sail exhibiting a slight weather helm. They are middle of the road as far as performance. Some have found them to be a bit tender, but that is inherent in their design and they do stiffen up after 15-20 degrees of heel and have good ultimate stability. Owners have been known to throw an extra 300 lbs. of ballast in the bilges which they claim helps.

Overall the boat’s design classically seaworthy, in rough seas these designs are well suited to heaving-to or laying ahull.

Specifications

LOA: 27′ 2″
LWL: 19’ 9″
Beam: 8′ 0″
Draft: 4′ 0″
Displacement: 6,600 lbs.
Ballast: 2,575 lbs. (encapsulated lead)

Sail Area: 340 sq. ft.

Fuel: 22 US Gal.
Water: 20 US. Gal.

Engine: Atomic 4 petrol / Westerbeck 10hp diesel / 15hp outboard

Designer: Carl Alberg
Builder: Bristol Yachts
Year Introduced: 1965
Year Ended:1978

Buyers Notes

You can usually find a Bristol 27 in the $5k-10k USD range, sometimes even cheaper, so it’s definitely priced to be a good first boat. They had good construction and now well over forty years, some boats are showing their age.

The hull to deck join has become prone to leaks, not that surprising for its age, and sometimes this can be a hard problem to fix properly. Also age related, are superficial non-structural gelcoat cracks and crazes. Try and get a model with an inboard engine.

Similar Boats

Pearson Triton 28
Alberg 30
Albin Vega 27
Cape Dory 27
Halcyon 27

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s